How to Apply Multicolor Granite-Effect Paint (Water-in-Water & Water-in-Sand): A Step-by-Step Guide
Published 2026-10-28 · Kangwangqi technical team · All articles

Multicolor granite-effect paint – sold as water-in-water (水包水) and water-in-sand (水包砂) – lets a contractor give a facade the look of polished or flamed granite at a fraction of the weight and cost of stone cladding. The finish is only as good as the process behind it. This guide sets out the full application sequence used by our technical team, with the curing times and spray settings from our instruction sheets, and practical notes for contractors and distributors working in African climates.
Why contractors choose multicolor paint instead of stone or tiles
- Very light and safe. The finished coating weighs about 1 kg/m² – roughly 1/6 of real stone paint, 1/40 of dry-hung stone and 1/20 of ceramic tiles. Our water-in-sand sheet puts the load on the building at under 5 kg/m², against about 40 kg/m² for dry-hung stone. Nothing can fall off a high-rise facade.
- Fast. One trained sprayer can cover about 120 m² per day, and colours can be combined freely.
- Clean. It is a water-based coating with a smooth, water-repellent surface, so dust and dirt do not soak in.
- Works almost anywhere. Concrete, precast concrete (PC) panels, ALC panels, fibre-cement boards and complex mouldings can all be coated.
- Cost. Slightly more than ordinary real stone paint, far less than dry-hung stone.
Water-in-water gives a smoother granite look. Water-in-sand contains natural quartz sand, so it forms a textured granite surface in a single sprayed pass, without spraying a separate texture base coat first. Our water-in-sand is made to GB/T 9756-2018 and GB 18582-2020.
The system at a glance
| Step | What to do | Interval (23 ± 2 °C) |
|---|---|---|
| 1. Protect | Mask windows, door frames, plants and floors | – |
| 2. Substrate | Remove hollow and loose areas, clean, fill cracks | Repairs cure 5–7 days |
| 3. Putty | Flexible levelling putty 1–2 coats, sand smooth | Cure 15–20 days (moisture < 10 %, pH < 10) |
| 4. Smoothing coat | Flexible smoothing compound 2–3 coats, fine sanding | 12 h between coats; 24 h before primer |
| 5. Primer | Sealing primer 1–2 coats by roller or spray | 6 h until fully dry |
| 6. Multicolor | Spray 1–2 coats with the special gun | 12 h between coats; 24 h dry |
| 7. Clear topcoat | Spray 1–2 coats | 4–6 h between coats |
| 8. Cure | Protect the facade from damage | 7 days |
For water-in-sand our instruction sheet gives the coating build-up as penetrating primer → same-colour mid coat → water-in-sand → silicone-acrylic topcoat.
Step 1 – Protect the site
Before work starts, walk the building and decide what must not be sprayed. Cover window sills, door frames, trees, paving and any finished surfaces with plastic film. Overspray from a multicolor gun travels further than from a roller, and it is far cheaper to mask than to clean.
Step 2 – Inspect and repair the substrate
- Check the whole wall for cracks and hollow (drummy) areas. Chip off anything hollow, half-detached or loose.
- On old walls, wash off old coatings and loose dust.
- Use a wire brush or sandpaper to remove dust, grease and other contamination.
- Where the wall is very dusty, wash it down with a high-pressure water jet.
- Fill cracks, hollows and dents with exterior putty and let the repairs cure for 5–7 days.
- On insulation boards, the surface must be flat and free of burrs – sand off any burrs.
Step 3 – Putty and smoothing
- Apply flexible levelling putty in 1–2 thin coats. The aim is a flat wall, not a thick layer.
- On tiled or mosaic walls, first apply a full coat of bonding agent, then a full coat of tile-renovation putty, then level.
- Sand the putty with wet-and-dry abrasive paper to remove dust and burrs.
- Let the putty cure for 15–20 days at 23 ± 2 °C, until the substrate moisture content is below 10 % and the pH is below 10.
- Apply a flexible smoothing compound in 2–3 coats, 12 h apart, then let it dry for 24 h.
- Finish with fine wet sanding so the surface is flat and smooth for the paint.
Site note: on fresh render, the curing period is the step most often cut short. A multicolor finish over damp or highly alkaline render can blister or discolour – check moisture and pH before you prime, especially after the rainy season.
Step 4 – Prime
Apply the special sealing primer evenly with a wool roller or spray gun, in 1–2 coats. Wait until it is completely dry – about 6 hours at 23 ± 2 °C – before moving on. For water-in-sand, follow the primer with a mid coat in the same colour as the finish.
Step 5 – Spray the multicolor coat
- Spray evenly with the special multicolor spray gun in 1–2 coats.
- Nozzle size: about 3.0 mm for water-in-water and 3.5–4.0 mm for water-in-sand.
- Leave 12 hours between coats and let the finished multicolor layer dry for 24 hours before the topcoat.
Spray a sample board first and get the client to approve the colour and pattern before you start on the wall. Keep the gun distance and walking speed constant so the pattern stays even from one scaffold lift to the next.
Step 6 – Clear topcoat
Spray 1–2 coats of clear topcoat, 4–6 hours apart. The topcoat protects the pattern and helps the surface shed dirt and rain. Our silicone-acrylic clear topcoat is available in gloss or matte.
Step 7 – Cure and clean up
The coating needs 7 days at 23 ± 2 °C to form a fully hardened film. Do not let anyone damage it in that time. One day after the last coat, remove the protective film, then clean the site and the ground.
Rules that prevent most failures
- Do not stir hard. Vigorous mixing breaks up the coloured particles and ruins the pattern.
- Do not add water and do not mix in any other material.
- Use an opened can in one go wherever possible.
- All intervals above are at 23 ± 2 °C. In cool or humid weather drying is slower – do not shorten the intervals just because the surface feels dry.
- Do not spray if rain is likely before the coat has dried, and protect fresh work with sheeting.
Notes for distributors
Multicolor paint is a system sale: putty, primer, mid coat, multicolor and topcoat. Stocking the full set – and a sample board for each colour scheme – lets your contractor customers buy everything from you and makes problems much easier to trace. Spray guns with the right nozzle sizes are a useful add-on. Ask us for colour schemes, sample boards and the technical data for each component.
Related products: Multicolor Granite-Effect Paint, Real Stone & Stone-Effect Exterior Paint, Exterior Acrylic Wall Paint. See our facade project photos.
Next steps
Related products:
Get a quote directly: tell us the product, application, area (m²) or quantity and destination port via the quote request form, WhatsApp or email.
Optional background: Available documents are listed with their applicable products on our certificates page. Contact us to confirm documentation for your selected coating. You can also read about our factory in Shunde.
