Metal Roof Waterproofing: Sealing Leaking and Rusty Corrugated Roofs

Corrugated and sheet metal roofs cover a large share of homes, warehouses, schools and workshops in Africa. They are quick to build, but over the years laps open, screws loosen and rust spreads until the roof leaks in every storm. A liquid rubber coating can seal and restore many of these roofs without replacing the sheets. This guide explains when coating is the right repair and how to do it.
The problem
Metal roofs leak for predictable reasons. The sheets expand in the midday sun and contract at night or in rain, so fixings work loose and laps open a little more each season. Rust starts around screw holes, laps and cut edges, especially in humid and coastal air. Gutters, ridges and flashings collect water and debris. Low-grade roof paints are too rigid for this movement: they crack, chalk and peel, and the leaks return.
A flexible coating that moves with the sheets and bridges laps, screw heads and hairline gaps is the usual answer – provided the steel underneath is still sound. If sheets are rusted through over large areas, replace those sheets first.
Recommended Kangwangqi products
- Liquid Rubber Roof Waterproofing Coating – The main product for this job. The acrylic-based elastomeric film stays flexible, follows the expansion and contraction of metal sheets and seals gaps, joints and hairline cracks. It is UV-stable, low-odour and brushed on cold, and it can also recolour faded roofs (for example barn red; other colours on request).
- Anti-Rust Paint – For exposed steel: treat rusty fixings, cut edges and structural steel with an anti-rust primer before coating. Options include a water-based epoxy zinc-rich primer.
- Polyurea Waterproofing Coating – For industrial metal roofs and structures where a tougher protective layer is required. The system depends on the grade – ask for the TDS.
Surface preparation
- Inspect the whole roof: loose or missing fixings, open laps, holes, rusted-through areas, damaged flashings and gutters.
- Replace sheets that are rusted through and renew badly corroded fixings.
- Clean off dirt, moss, loose rust and flaking old paint; wash off salt and dust and let the roof dry.
- Treat remaining rust on exposed steel with an anti-rust primer where needed.
- Tighten and seal fixings and laps before coating the main area.
Application steps
- Reinforce laps, screw heads, ridges, flashings and penetrations first – these are where most leaks start.
- Brush the coating over the whole roof in the number of coats we recommend for your roof condition.
- Work from the top of the roof down and finish each section completely.
- Avoid the hottest hours on metal sheets, which can get very hot; morning and late afternoon give better working time.
- Do not coat if rain is expected before the film has set; inspect the details after the first heavy rain.
These are general steps. Always follow the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for the product and grade you use; values not shown on our product pages are provided in the TDS on request.
Buyer checklist – what to send us
- Roof area in m² and sheet type (corrugated, long-span, trapezoidal)
- Roof condition: light rust, heavy rust, open laps, holes
- Whether the building is near the coast or in an industrial area
- Colour required (e.g. barn red, other colours on request)
- Whether exposed steel also needs anti-rust primer
- Destination port, quantity and timing before the rainy season
- Please also share: project location, area (m²), substrate, existing coating condition and quantity – we use these to recommend the product, grade and TDS values for your job.
FAQ
Can a liquid rubber coating stop a leaking metal roof?
In many cases, yes – if the sheets are still sound. The coating seals laps, screw heads and hairline gaps and stays flexible as the sheets move. Sheets that are rusted through should be replaced first.
Do I need to remove all the rust first?
Remove loose and flaking rust and old paint and treat exposed steel with an anti-rust primer. Firmly bonded material can stay, but the surface must be clean and dry.
Does the coating change the colour of the roof?
Yes. It can restore and recolour faded roofs – for example barn red. Other colours are available on request.
Is a torch or heat needed?
No. The coating is brushed on cold, with low odour.
What is the minimum order?
The liquid rubber roof coating has a minimum order of 200 kg. Send us the roof area and we will calculate the quantity.
Next steps
Get a quote: send the product, area (m²) or quantity and destination port via the quote request form, WhatsApp or email. Reference prices on our product pages are EXW factory, Foshan; FOB / CIF to your port quoted on request.
Documents: Available documents are listed with their applicable products on our certificates page. Contact us to confirm documentation for your selected coating.
Related guides:
- Polyurea vs Liquid Rubber Roof Waterproofing: Which Coating Should You Choose?
- Flat Roof Waterproofing in Hot, Humid African Climates: Causes of Leaks, Coatings and Application
- Roof Waterproofing Before the Rainy Season in Lagos: A Buyer and Contractor Guide
More application guides:


