Coatings manufacturer supplying distributors & contractors across Africa✉ [email protected] · WhatsApp +86 135 1658 7780 · Find a distributor
Request a Quote
Application guide · Metal

Steel Structure Anti-Rust Coating: Surface Preparation, Primer and Topcoat

Anti-rust paint for steel structures by Kangwangqi
Anti-rust paint for steel structures by Kangwangqi. Packaging shown is representative.

Steel workshops, warehouses, space frames, gates, railings and tanks rust quickly in humid and coastal air. Once rust takes hold it spreads under the paint, and the repair costs far more than the original coating. This guide explains how to plan an anti-rust system for steel, using the preparation and application data from our steel-structure paint instruction sheet.

The problem

Steel corrodes when moisture and oxygen reach the bare metal; salt and industrial pollution speed this up. Paint usually fails first at sharp edges, welds, bolts and areas that were poorly cleaned, then rust creeps under the film and lifts it. In hot, humid climates, condensation on cool steel in the morning adds to the problem.

A good result depends far more on surface preparation and the primer/topcoat system than on any single coat of paint.

Recommended Kangwangqi products

Surface preparation

  1. Remove oil, loose rust and old paint.
  2. Grind off weld beads, spatter and hardened layers; round cut and sheared edges to R2.
  3. Blast to Sa 2.5, or power-tool clean to St 2 where blasting is not possible.
  4. Paint within 6 hours of blasting, before new rust forms (water-based steel-structure grade instruction sheet; for other primers follow their TDS).
  5. Keep the steel dry and free of dust and salt before priming.

Application steps

  1. Stir the paint well; apply by brush or spray.
  2. For the water-based steel-structure grade: if the paint is too thick, add deionised water while stirring – no more than 10 %.
  3. Apply primer first, then the topcoat, in the system and film thickness we recommend for your environment.
  4. Pre-coat edges, welds and bolts by brush so they get full coverage.
  5. For the water-based steel-structure grade, do not paint below 5 °C or above 85 % relative humidity (other products: see their TDS); keep the area ventilated and do not paint outdoors in rain, snow or fog (cover fresh paint with tarpaulin).

These are general steps. Always follow the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for the product and grade you use; values not shown on our product pages are provided in the TDS on request.

Buyer checklist – what to send us

FAQ

Do I need a zinc-rich primer?

Zinc-rich primers are widely used on steel because zinc gives sacrificial (galvanic) protection. Tell us the environment and we will recommend the primer and topcoat system.

Can I paint over rust?

Loose rust, oil and old paint must be removed. Prepare to Sa 2.5 by blasting or St 2 with power tools for the best result.

How soon after blasting must I paint?

For our water-based steel-structure grade, within 6 hours of blasting, before new rust forms. For other primers, follow their TDS.

Can the paint be thinned?

The water-based steel-structure grade can be thinned with deionised water while stirring – no more than 10 %.

What finishes are available?

Topcoats in matte, semi-gloss and high gloss, in colours from our K7 / RAL colour card. A water-based fluorocarbon finish is also available.

Next steps

Get a quote: send the product, area (m²) or quantity and destination port via the quote request form, WhatsApp or email. Reference prices on our product pages are EXW factory, Foshan; FOB / CIF to your port quoted on request.

Documents: Available documents are listed with their applicable products on our certificates page. Contact us to confirm documentation for your selected coating.

Related guides:

More application guides:

All application guides →

Planning this job? Request a Quote WhatsApp

Products for this application

Anti-Rust Paint
Water-based
Industrial & Metal

Anti-Rust Paint

Protective primer and topcoat options for steel and metal surfaces, including water-based epoxy zinc-rich primer.

From US$2.00/kg (EXW factory, Foshan)

  • ◐Matte · Semi-gloss · High gloss
  • 💧Water-based
  • ▦Steel & metal
Fluorocarbon Paint
Water-based
Industrial & Metal

Fluorocarbon Paint

Water-based fluorocarbon finish coating for architectural and metal applications.

From US$7.00/kg (EXW factory, Foshan)

  • ◐Matte · Semi-gloss · High gloss
  • 💧Water-based
  • ▦Steel & metal, Masonry & render

Looking for a reliable coatings supplier?

Tell us your project, market and quantities. We reply with product options, technical data and a quotation.

Request a Quote Chat on WhatsApp Email us
WhatsApp