Coatings manufacturer supplying distributors & contractors across Africa✉ [email protected] · WhatsApp +86 135 1658 7780 · Find a distributor
Request a Quote
Application guide · Waterproofing

Basement and Foundation Waterproofing: Coatings, Preparation and Buyer Checklist

Kangwang K11 & JS cementitious waterproof slurry – yellow Kangwang bucket on a waterproofing job site
K11 and JS cementitious waterproof slurry for basements and below-grade concrete. Packaging shown is representative.

Basements, underground rooms, foundation walls and lift pits are in contact with damp soil and, in the rainy season, often with water under pressure. Once a basement leaks, repairs are difficult and costly. This guide explains where the water comes from, which Kangwangqi coatings are used below ground, and how to plan the work.

The problem

Water reaches below-grade concrete in several ways: rain soaking into the backfill, a high water table in the wet season, poor drainage around the building and capillary moisture rising through the slab. It enters through construction joints, tie-bolt holes, honeycombed concrete, cracks and pipe entries. The result is damp walls, efflorescence (white salt deposits), peeling paint, mould and, in the worst case, running water.

Waterproofing is most effective on the side where the water comes from (the outside of the wall), applied during construction before backfilling. On existing basements the work is often done from the inside. Which system is suitable depends on the water pressure, so describe the situation to us before you order.

Recommended Kangwangqi products

Surface preparation

  1. Stop active leaks first. Running water must be stopped with a suitable plugging material before any coating is applied.
  2. Remove laitance, form oil, loose concrete, old paint and efflorescence down to sound concrete.
  3. Repair honeycombing, tie-bolt holes, cracks and construction joints.
  4. Treat details such as pipe entries and wall–floor junctions before the main area.
  5. Control moisture: follow the TDS on whether the surface should be dry or damp for the product you use.

Application steps

  1. Reinforce joints, corners and penetrations first.
  2. Apply the main coats over the whole area, to the thickness and number of coats in the TDS.
  3. On the outside of foundation walls, carry the coating above final ground level.
  4. Protect the cured coating before backfilling, and do not backfill against an uncured coating.
  5. Improve drainage around the building where possible – it reduces the load on any waterproofing system.

These are general steps. Always follow the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for the product and grade you use; values not shown on our product pages are provided in the TDS on request.

Buyer checklist – what to send us

FAQ

Can a basement be waterproofed from the inside?

Often, yes, especially on existing buildings where the outside cannot be reached. Whether a coating is suitable depends on the water pressure. Describe the situation and ask us which grade to use.

Which product is used for basements?

K11 cementitious slurry is used for basements and wet areas; polyurea and liquid rubber are also used on basements. We recommend the system after we know the substrate, the water condition and the finish.

Can I coat over a wall with running water?

No. Active leaks must be stopped first; coatings need a sound, prepared surface.

What about salt deposits on the wall?

Efflorescence must be brushed and washed off and the cause (water moving through the wall) addressed before coating.

Do you provide technical documents?

TDS and SDS are available on request; documents that we hold are listed on our certificates page with their applicable products.

Next steps

Get a quote: send the product, area (m²) or quantity and destination port via the quote request form, WhatsApp or email. Reference prices on our product pages are EXW factory, Foshan; FOB / CIF to your port quoted on request.

Documents: Available documents are listed with their applicable products on our certificates page. Contact us to confirm documentation for your selected coating.

Related guides:

More application guides:

All application guides →

Planning this job? Request a Quote WhatsApp

Products for this application

Kangwang K11 & JS cementitious waterproof slurry – yellow Kangwang bucket on a waterproofing job site
Water-based
Waterproofing

K11 & JS Cementitious Waterproof Slurry

Brush-applied waterproof slurries for wet areas and below-grade concrete: K11 nano-type waterproof slurry and JS polymer waterproof slurry.

From US$1.00/kg (EXW factory, Foshan)

  • ◐Finish: on request
  • 💧Water-based (polymer-modified cementitious)
  • ▦Concrete, Masonry & render
Liquid Rubber Roof Waterproofing Coating
Waterproofing

Liquid Rubber Roof Waterproofing Coating

Acrylic-based liquid rubber coating that cures into a flexible, UV-stable waterproof membrane for flat, low-slope and metal roofs.

From US$2.00/kg (EXW factory, Foshan)

  • ◐Matte
  • 💧Acrylic elastomeric (liquid rubber)
  • ▦Concrete, Metal

Looking for a reliable coatings supplier?

Tell us your project, market and quantities. We reply with product options, technical data and a quotation.

Request a Quote Chat on WhatsApp Email us
WhatsApp