Concrete Water Tank Waterproofing with Polyurea Coating

Concrete water tanks – on rooftops, at ground level or underground – are essential where mains supply is irregular. A leaking tank wastes water, damages the structure around it and can let contamination in. This guide covers how polyurea waterproofing coating is used to protect concrete tanks, and what to check before you order.
The problem
Concrete tanks are under constant water pressure. Shrinkage cracks, construction joints, tie-bolt holes and pipe inlets and outlets are the usual leak points. Rooftop tanks are also exposed to strong sun and daily temperature changes, so the concrete moves and cracks open. Coatings that are rigid or poorly bonded crack or blister under these conditions.
Polyurea coatings form a continuous, seamless membrane without joints or laps and are generally chosen where flexibility and abrasion resistance matter – which is why water tanks are one of the listed uses of our polyurea waterproofing coating.
Recommended Kangwangqi products
- Polyurea Waterproofing Coating – Used on roofs, basements, water tanks, bridges and industrial structures, on concrete and metal. Exact values (elongation, tensile strength, curing time) and the application method depend on the grade – ask us for the Technical Data Sheet for your tank.
Surface preparation
- Drain and clean the tank completely; remove sludge, algae and loose material.
- Remove old coatings that are no longer bonded, laitance and contamination down to sound concrete.
- Repair cracks, honeycombing, tie-bolt holes and joints; seal around pipe inlets and outlets.
- Let the concrete dry to the condition required by the TDS, and apply a primer if the grade requires one on concrete.
- Ventilate the tank well during preparation and application, and follow the SDS for safe working in confined spaces.
Application steps
- Reinforce joints, corners and pipe penetrations first.
- Apply the coating to walls and floor to the film thickness specified in the TDS.
- Check for pinholes and thin spots and repair them before the coating is complete.
- Allow the coating to cure fully, as stated in the TDS, before filling the tank.
- Flush the tank before putting it into service.
These are general steps. Always follow the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for the product and grade you use; values not shown on our product pages are provided in the TDS on request.
Buyer checklist – what to send us
- Tank type: rooftop, ground-level or underground; concrete or steel
- Internal area in m² (walls plus floor) and capacity
- Stored water: drinking water, process water, rainwater, fire water
- Condition: new tank or repair of a leaking tank
- Documents required by your client or local authority
- Destination port and quantity
- Please also share: project location, area (m²), substrate, existing coating condition and quantity – we use these to recommend the product, grade and TDS values for your job.
FAQ
Can the coating be used in drinking-water tanks?
Drinking-water (potable) contact normally requires a specific approval. Our site does not list a drinking-water approval for any product. If your tank holds drinking water, tell us before ordering so we can confirm what documents are and are not available.
How long before I can fill the tank?
Only after the coating has fully cured. The curing time depends on the grade and temperature – follow the TDS.
Can polyurea be applied on a steel tank?
Our polyurea coating is listed for concrete and metal surfaces. Steel must be cleaned of rust and contamination first; ask us for the system for your tank.
How much coating do I need?
Coverage depends on the required film thickness and the substrate. Send us the tank dimensions and we will recommend the quantity.
Is K11/JS slurry suitable for tanks?
Our K11/JS slurries are listed for bathrooms, kitchens, balconies, basements and roofs under tiles. For water tanks we recommend asking us about polyurea.
Next steps
Get a quote: send the product, area (m²) or quantity and destination port via the quote request form, WhatsApp or email. Reference prices on our product pages are EXW factory, Foshan; FOB / CIF to your port quoted on request.
Documents: Available documents are listed with their applicable products on our certificates page. Contact us to confirm documentation for your selected coating.
Related guides:
More application guides:
