Coatings manufacturer supplying distributors & contractors across Africa✉ [email protected] · WhatsApp +86 135 1658 7780 · Find a distributor
Request a Quote
Application guide · Waterproofing

Bathroom and Wet-Area Waterproofing Under Tiles with K11 & JS Slurry

Kangwang K11 & JS cementitious waterproof slurry – yellow Kangwang bucket on a waterproofing job site
K11 and JS cementitious waterproof slurry by Kangwangqi. Packaging shown is representative.

Leaks from bathrooms, showers, kitchens and balconies damage ceilings, walls and finishes in the rooms below, and they are expensive to fix once the tiles are laid. Tiles and grout on their own are not waterproof. The reliable approach is a waterproofing layer under the tiles. This guide shows how to use K11 and JS cementitious waterproof slurry in wet areas.

The problem

Water in a wet room finds its way through grout joints and around fittings. Once it reaches the screed and slab, it travels to the weakest point: the junction between floor and wall, the gap around a pipe or the edge of a floor drain. Typical signs are damp patches and stains on the ceiling below, blistering paint on the other side of a shower wall and loose tiles.

A cementitious waterproof slurry is brushed on as a thin coating, bonds to concrete and masonry and is then tiled over. Because it is part of the build-up under the tiles, it has to be done properly before tiling starts.

Recommended Kangwangqi products

Surface preparation

  1. Check the substrate: the screed or slab must be sound, with the falls to the floor drain already formed.
  2. Clean off dust, loose material, oil and old adhesive; there must be no standing water.
  3. Fix pipes and drains in their final position before waterproofing.
  4. Round or fill sharp internal corners so the coating can be applied continuously.
  5. Pre-dampen if the TDS requires it – follow the instructions for the grade you use.

Application steps

  1. Reinforce corners, floor–wall junctions, pipe penetrations and floor drains first.
  2. Mix the slurry exactly as stated in the TDS for the grade.
  3. Brush on the first coat over the floor and up the walls, to the height your local practice or the project specification requires around showers and baths.
  4. Apply the second coat in the direction recommended in the TDS once the first coat allows.
  5. Many contractors carry out a flood (ponding) test before tiling, for the period the specification requires.
  6. Tile over the cured slurry with a suitable tile adhesive.

These are general steps. Always follow the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for the product and grade you use; values not shown on our product pages are provided in the TDS on request.

Buyer checklist – what to send us

FAQ

Are tiles and grout waterproof on their own?

No. Water passes through grout joints and around fittings. A waterproofing layer under the tiles is needed in bathrooms, showers and other wet areas.

What is the difference between K11 and JS?

We make two grades: K11 nano-type waterproof slurry, used for bathrooms, kitchens, basements and wet areas, and JS high-polymer waterproof slurry, used for roofs, exterior walls, balconies and parapets. Ask us which grade suits your project.

Can I tile directly over the slurry?

Yes. Slurries of this type are generally tiled over once cured. Use a suitable tile adhesive and follow the curing time in the TDS.

How much slurry do I need?

Consumption depends on the grade and the number of coats. Send us the floor and wall area and we will recommend the quantity.

Do you supply private-label packaging?

Yes. Private-label (OEM) packaging is available – see our OEM page.

Next steps

Get a quote: send the product, area (m²) or quantity and destination port via the quote request form, WhatsApp or email. Reference prices on our product pages are EXW factory, Foshan; FOB / CIF to your port quoted on request.

Documents: Available documents are listed with their applicable products on our certificates page. Contact us to confirm documentation for your selected coating.

Related guides:

More application guides:

All application guides →

Planning this job? Request a Quote WhatsApp

Products for this application

Kangwang K11 & JS cementitious waterproof slurry – yellow Kangwang bucket on a waterproofing job site
Water-based
Waterproofing

K11 & JS Cementitious Waterproof Slurry

Brush-applied waterproof slurries for wet areas and below-grade concrete: K11 nano-type waterproof slurry and JS polymer waterproof slurry.

From US$1.00/kg (EXW factory, Foshan)

  • ◐Finish: on request
  • 💧Water-based (polymer-modified cementitious)
  • ▦Concrete, Masonry & render

Looking for a reliable coatings supplier?

Tell us your project, market and quantities. We reply with product options, technical data and a quotation.

Request a Quote Chat on WhatsApp Email us
WhatsApp