Parking Garage and Car Park Floor Coating: What to Use and How to Apply It

Car parks in shopping centres, office buildings, apartments and hotels take constant tyre traffic, oil drips and water carried in on wheels. A coated floor is easier to clean and lets you mark bays, lanes and arrows clearly. This guide covers floor coating for covered car parks and garages, and what to use for outdoor driveways.
The problem
Bare concrete in car parks wears and dusts under turning tyres, especially on ramps and at entrances. Oil and fuel drips soak in and stain. Water and grit carried in on tyres collect in low spots. Faded markings make the car park harder to use. In basements, damp concrete makes all of this worse.
An epoxy floor coating seals the concrete with a seamless, easy-to-clean surface and can be combined with coloured lane and bay markings, like the car parks in our project photos.
Recommended Kangwangqi products
- Epoxy Colored-Sand Self-Leveling Floor Coating – Parking areas and garages are among the listed uses. Approx. 1.5–2.5 kg/m², two-component (A : B = 8 : 1), water-based and solvent-free. The product page describes it as designed for wear, heavy loads and impact and for resistance to many acids, alkalis, salts and oils; tell us the vehicle types, ramps and the oils or cleaning chemicals involved so we can confirm suitability.
- Resin Washed Stone Paving Binder (Permeable Epoxy) – For outdoor driveways, compounds and paths: a clear epoxy binder for permeable resin washed stone paving with a non-slip textured finish, so rainwater drains through instead of ponding.
Indoor car parks vs outdoor areas
Parking areas and garages are listed uses of the epoxy colored-sand floor coating. For open-air decks exposed to strong sun and rain, tell us the conditions before you order and we will confirm whether the system suits them; for outdoor paving, our resin washed stone binder (approx. 5 kg/m²) gives a permeable, non-slip surface. For bay lines and arrows, choose a contrasting colour from our K7 / RAL colour card.
Surface preparation
- Check moisture in basement slabs; damp must be dealt with before coating.
- Grind or shot-blast to remove laitance, old coatings and tyre marks.
- Degrease oil and fuel stains thoroughly.
- Repair potholes, cracks and broken joint edges; plan drainage falls and drains.
- Vacuum the floor and mask drains, columns and walls.
Application steps
- Apply primer, mid-coat and top-coat as one system.
- Mix A and B at 8 : 1 by weight; apply within the pot life (approx. 40 min at 25 °C).
- Trowel, then spiked-roll to remove bubbles.
- Apply at 10–30 °C and relative humidity below 75 %.
- Mark bays, lanes and arrows after the floor has dried. The product page gives normal use after 7 days of curing; confirm in the TDS when vehicles can be allowed for your temperature and build-up.
These are general steps. Always follow the Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for the product and grade you use; values not shown on our product pages are provided in the TDS on request.
Buyer checklist – what to send us
- Floor area in m² and number of levels
- Covered (indoor/basement) or open to sun and rain
- Ramps, entrances and turning areas
- Base colour and marking colours
- Whether bays and arrows are marked by you or by your contractor
- Destination port; epoxy minimum order is 100 kg
- Please also share: project location, area (m²), substrate, existing coating condition and quantity – we use these to recommend the product, grade and TDS values for your job.
FAQ
Can cars drive on the floor soon after coating?
Not straight away. The product page gives foot traffic after 24–48 hours and normal use after 7 days of curing; confirm with the TDS when vehicles can be allowed for your temperature, humidity and build-up.
Which colour should I choose?
Many car parks use a grey or green base with white or yellow markings. Choose from our K7 / RAL colour card; custom colours are possible for project orders.
Will oil damage the floor?
The product page describes the coating as resistant to many acids, alkalis, salts and oils. Tell us which oils, fuels and cleaning chemicals are used so we can confirm, and clean spills promptly to keep the floor in good condition.
Can I use the same coating on an outdoor driveway?
For outdoor driveways and compounds we suggest our resin washed stone paving binder, which forms a permeable, non-slip surface. For open-air decks, ask us first.
How do I estimate the quantity?
Theoretical consumption is approx. 1.5–2.5 kg/m². Use our coverage calculator and send us the floor plan for a quotation.
Next steps
Get a quote: send the product, area (m²) or quantity and destination port via the quote request form, WhatsApp or email. Reference prices on our product pages are EXW factory, Foshan; FOB / CIF to your port quoted on request.
Documents: Available documents are listed with their applicable products on our certificates page. Contact us to confirm documentation for your selected coating.
Related guides:
More application guides:


